In order to install an optional 3rd brake light, the center hole on your wheel must be 2 - 1/2" or larger. Installation only requires you to splice the light onto your factory light wiring... more
This bracket will allow you to relocate your rear license plate to the center of your spare tire. You can also purchase this bracket with optional PlateLITE as a Combo... more
This bumper is made from ¼" CNC Laser cut and bent steel for consistent quality. Tapers down and back to protect the factory lower front cross frame and Sway-bar disconnect unit(if equipped)... more
Rock Hard Rear Bumper/Tire-Carriers are made out of 3/16" x 2" x 4" thick tubing with ends that are boxed in. They have 2 sets of holes which mount to your Jeep frame in a standard position or can be raised 1" to increase departure angle and/or compensate for body lift... more
The Rock Hard Frame Kit is recommended with tires larger than 33" or with Rock Rack or Can Mounts. TJ Kit shown with 2 of 3 possible bolts installed, requires drilling 3rd hole.
Rock Hard Tank Mounts bolt on and work with NATO or USA cans. Left and right side sold separately. Requires Rock Hard Rear Bumper/Tire-Carrier for installation.
The Rock Hard Jeep JK Wrangler Rear Bumper/Tire-Carrier is the only JK rear bumper on the market today that is made out of 1/4" thick plate steel... more
Rockhard 4x4 Parts 2007 JK Front Shorty Bumper Is made from 1/4" plate to withstand Rockhard Abuse. Tapers down and back to protect the Factory Lower front cross frame and Sway-bar Disconnect unit (if equipped)... more
The Rock Hard Frame Kit is recommended with tires larger than 33" or with Rock Rack or Can Mounts. TJ Kit shown with 2 of 3 possible bolts installed, requires drilling 3rd hole.
Made of 3/16”x2”x4” thick metal tubing with 1/4” plate ends. Holds up to a 38” tire. Comes standard with a Integrated class 2 hitch receiver, CB antenna mount, Horizontal Hi-Lift mount with padlock provision, two 5/8” x 1/2” CNC machined and D-Ring shackle mount with welded tabs... more
This Rock Hard 4x4 Top of the Line Full Width front Bumper is made from 1/4” CNC laser cut and bent Steel Plate for consistent quality. Comes pre-drilled to accept our bolt on winch plate and brush guard... more
Rock Hard Front Bumpers are designed for heavy duty use in the rocks. made of 3/16" x 2" x 4" tubing and come with an integrated CNC laser cut winch plate, roller fairlead mount and holes for lights at outer edge of winch plate... more
Jeep Parts & Jeep Accessories Take your Jeep to the next level with the parts found on our site. We are a leading Jeep accessories retailer, providing performance products for our customers. We work hard to give you the best information to turn your vehicle into a top-notch ride. Whether you are looking for 4wd suspension parts & accessories or want improved Jeep performance, we have the parts & Jeep accessories you need.
The terms Quadratec and Essentials are Registered Trademarks of Quadratec Incorporated, Registered in U.S. Patent and Trademark Office. All manufacturers names, numbers, symbols and descriptions are used for reference purposes only, and it is not implied that any part listed is the product of these manufacturers or approved by any of these manufacturers.
*Jeep, Wrangler, Rubicon, Renegade, CJ, Quadra-Trac and the Jeep Grille Design are registered trademarks of Chrysler LLC. Quadratec, Inc, has no affiliation with Chrysler LLC. Throughout this website and catalog the terms Jeep, Wrangler, MOPAR®, & Rubicon are used for identification purposes only. Geo is a registered trademark and Tracker is a registered trademark of the General Motors Company. Sidekick and Samurai are trademarks of Suzuki Motor Corporation. Amigo is a product of Isuzu Motors Limited. Chevrolet, the Chevrolet Emblem, S Series, GMC, GMC Truck, Chevy, Vortec and Sonoma are registered trademarks of the General Motors Company. Expedition, F-Series, F-150, F-250, F-350, Super Duty and Flare Side are registered trademarks of the Ford Motor Company. All other marks, names, and logos mentioned on this web site are the property of their respective owners.
Throughout this web site all the preceding marks & logos are used for identification purposes only. Quadratec has no affiliation with the Chrysler LLC, MOPAR®, General Motors Company, Ford Motor Company, Suzuki Motor Corporation or Isuzu Motors Limited. It is not implied that any part listed is a product of, or approved by Chrysler LLC, General Motors Company, Ford Motor Company, Suzuki Motor Corporation or Isuzu Motors Limited.
Quadratec, Inc. is sometimes mis-searched as Quadartec and Quadratech, we have no affiliation with either. [4]
