ARB 3450150 Quadratec Edition Front Stubby Bull Bar Bumper for 87-06 Jeep® Wrangler YJ, TJ & Unlimited
Quadratec Edition Bull Bar construction starts with a 3mm thick steel plate thats laser cut to form the component parts. These parts are then folded to make up the sections of the bull bar. CNC machines ensure consistency and quality results as the formed panels are fully welded utilizing robotic welders and grinders for a precision finish. The 60mm OD bull bar hoops are 2.6mm thick and mandrel bent for even wall thickness across all sections. Final finishing begins with vigorous steel shot blasting followed by a phosphate metal prep solution bath. Bars are hung to dry on a conveyer and sent though an automated powder coating booth and oven baked to a rich and durable finish.
The integrated winch and fairlead mount plates allow maximum bumper approach angles and winch protection and tested to endure extreme winching loads. The securely welded light mount tabs are ideally located and spaced 12 apart. Fully welded D-ring mounts accommodate ¾ clevis pins into cross section plates and provide additional structural rigidity to the bar. When installed, ARB Bull Bars act as an integral cross member to spread impacts and winching loads evenly.
Air Bag Compatibility
To ensure airbag compatibility, ARB recognizes frontal crush characteristics through computer models and replicates the crush rate into the design of each bull bar and its mounting system. This method enables engineers to achieve maximum possible vehicle and passenger protection without affecting proper air bag deployment.
1. Does Not work with WARN PowerPlant & M8274 Winches.
2. Does Not work with Superwinch 9.0 Winches.
3. Fits WARN 9.5TI/SI, HS9500I, XD9000, XD9000I, M8000, XP9500 Winches & VR Series.
- Features: Bumper Hoop, Integrated Winch Mount
- Color: Black
- Style: Stubby Bumper
- Material: Steel
Jeep Wrangler (TJ)
- 2006 Jeep Wrangler (TJ)
- 2005 Jeep Wrangler (TJ)
- 2004 Jeep Wrangler (TJ)
- 2003 Jeep Wrangler (TJ)
- 2002 Jeep Wrangler (TJ)
- 2001 Jeep Wrangler (TJ)
- 2000 Jeep Wrangler (TJ)
- 1999 Jeep Wrangler (TJ)
- 1998 Jeep Wrangler (TJ)
- 1997 Jeep Wrangler (TJ)
Jeep Wrangler Unlimited (TJ)
- 2006 Jeep Wrangler Unlimited (TJ)
- 2005 Jeep Wrangler Unlimited (TJ)
- 2004 Jeep Wrangler Unlimited (TJ)
Jeep Wrangler (YJ)
- 1995 Jeep Wrangler (YJ)
- 1994 Jeep Wrangler (YJ)
- 1993 Jeep Wrangler (YJ)
- 1992 Jeep Wrangler (YJ)
- 1991 Jeep Wrangler (YJ)
- 1990 Jeep Wrangler (YJ)
- 1989 Jeep Wrangler (YJ)
- 1988 Jeep Wrangler (YJ)
- 1987 Jeep Wrangler (YJ)
I'm a little confused with the mounting hole line up. It is setup for all 6 bolts, but to get the bottom bolt lined up with the frame, you only have the rear mount hole lined up on top to use. So only 4 bolts would work on my 06 TJ. The other issue was on the Quadratec Q9500 Stealth winch mounting, I had to take a die grinder to open up the clearance between the top back rail of the bumper to clear the positive cable post from motor that goes into the solenoid. Other than that it went great. My last recommendation to ARB is, to fab the shackle
D-ring mounts to be a little thicker to avoid the D-Rings from rattling and let them fit a snug. Can't wait to hit the trails and try everything out.