« Back to product
Andy P.
Will these work on a 2021 JT with halogen lights IF connected to one of my AUX switches?
Yes, the Oracle Lighting 5881-504 Rear Bumper LED Reverse Lights will work on your 2021 Jeep Gladiator JT, even if it's equipped with halogen lights.
The product description indicates that these lights are compatible with the 2021 Gladiator JT. Installation typically involves tapping into the existing reverse light wiring using the included T-taps or an optional plug-and-play harness.
While the standard installation involves connecting to the reverse light circuit, you can connect them to one of your AUX switches. This would allow you to control the lights independently of the reverse gear. However, this method will likely require some additional wiring and may not be a simple plug-and-play setup. You would need to run wiring from the AUX switch to the lights and ensure proper grounding.
Consider these options:
Standard Wiring: Connect the lights to the reverse light circuit using the included T-taps or an optional plug-and-play harness. This will make them activate automatically when you shift into reverse.
AUX Switch Wiring: Connect the lights to an AUX switch for independent control. This requires additional wiring but gives you the flexibility to turn them on whenever you need extra rear illumination.
If you choose to wire them to an AUX switch and are not comfortable with electrical work, it's recommended to have them professionally installed.
The product description indicates that these lights are compatible with the 2021 Gladiator JT. Installation typically involves tapping into the existing reverse light wiring using the included T-taps or an optional plug-and-play harness.
While the standard installation involves connecting to the reverse light circuit, you can connect them to one of your AUX switches. This would allow you to control the lights independently of the reverse gear. However, this method will likely require some additional wiring and may not be a simple plug-and-play setup. You would need to run wiring from the AUX switch to the lights and ensure proper grounding.
Consider these options:
Standard Wiring: Connect the lights to the reverse light circuit using the included T-taps or an optional plug-and-play harness. This will make them activate automatically when you shift into reverse.
AUX Switch Wiring: Connect the lights to an AUX switch for independent control. This requires additional wiring but gives you the flexibility to turn them on whenever you need extra rear illumination.
If you choose to wire them to an AUX switch and are not comfortable with electrical work, it's recommended to have them professionally installed.
Nathaniel B.
Can these be directly wired to an aux switch to use on demand vs only when in reverse? What is voltage/fuse requirement for the lights?
Yes, you can directly wire the Oracle Lighting 5881-504 Rear Bumper LED Reverse Lights to one of your AUX switches to use them on demand instead of only when in reverse. Many Gladiator owners have successfully done this.
The Oracle Lighting 5881-504 lights operate on 12 Volts DC, which is the standard electrical system voltage for your Jeep Gladiator.
Fuse Requirement: The product specifications mention a total of 30 high-powered LEDs with a total output of 1500 lumens (raw). While the exact current draw isn't always explicitly stated, it's good practice to use a 3-5 amp fuse for this pair of lights. This should provide adequate protection without being overly sensitive. It's always best to start with a lower amperage fuse and increase if it blows, but avoid using a fuse with a significantly higher rating than likely needed.
The Oracle Lighting 5881-504 lights operate on 12 Volts DC, which is the standard electrical system voltage for your Jeep Gladiator.
Fuse Requirement: The product specifications mention a total of 30 high-powered LEDs with a total output of 1500 lumens (raw). While the exact current draw isn't always explicitly stated, it's good practice to use a 3-5 amp fuse for this pair of lights. This should provide adequate protection without being overly sensitive. It's always best to start with a lower amperage fuse and increase if it blows, but avoid using a fuse with a significantly higher rating than likely needed.
BRIAN I.
Are these compatible with the Carnivore JT rear bumber?
No, these are for the OEM bumper.
Robert B.
Will these lights and the PNP harness work on my 22 JT with halogen rear lights?
This LED is only compatible with Gladiators that are factory equipped with LED Tail Lamps. This will work with halogen equipped Gladiators with use of a programmer. Thank you for the question.