« Back to product
Charlie L.
will this bumper allow me to add a front 2" hitch receiver
No, the Rampage Products 99306 Rock Rage Front Bumper does not include or provide accommodation for a front 2-inch hitch receiver; it features an integrated winch plate and dual D-ring shackle mounts.
Jason B.
Will this bumper fit a 2020 gladiator or do I need an adapter for it to match up to the frame bolts, I saw a video where they had to modify the bolt holes on a JL for this to fit. I am not talking about the fog lights but where the bumper mounts up to the frame of the Jeep.
Yes, this bumper will fit your 2020 Jeep Gladiator JT directly, and you do not need any adapters to match it up to the frame bolts.
Danyell M.
I have a JL sport. I purchased and installed the Rampage Rock Rage front Bumper 7-23 yesterday. My fog lights were not installed at the time of installation. Is there something else needed to install them?
Yes, you will need a few additional items depending on your Jeep Sport's factory configuration:
Fog Light Brackets or Adapters: While the Rampage Products Rock Rage Front Bumper includes 4-inch recessed light receptacles designed to accept OE-style fog lights, the factory plastic bumper fog lights on many Wrangler JL Sport models do not mount directly into aftermarket steel bumpers without specific adapter brackets or replacement housings.
Wiring Extensions: Because the new aftermarket bumper positions the fog lights further forward or slightly different from the stock plastic bumper layout, your factory fog light wiring harness may not reach the bulbs without a short extension harness.
Fog Light Brackets or Adapters: While the Rampage Products Rock Rage Front Bumper includes 4-inch recessed light receptacles designed to accept OE-style fog lights, the factory plastic bumper fog lights on many Wrangler JL Sport models do not mount directly into aftermarket steel bumpers without specific adapter brackets or replacement housings.
Wiring Extensions: Because the new aftermarket bumper positions the fog lights further forward or slightly different from the stock plastic bumper layout, your factory fog light wiring harness may not reach the bulbs without a short extension harness.
Scott G.
Will the Rampage Rock Rage bumper (with Bull bar) allow me to continue to use my Curt front hitch and my Anglers Fish-N-Mate Surf-Mate Jr. cooler/Rod rack ?
Or will the Bull bar get in the way ?
Based on the design specifications and installation data for both the Rampage Rock Rage Front Bumper (99306) and CURT Front Mount Hitches, it is likely that you will encounter compatibility issues that could prevent you from using your Angler's Fish-N-Mate Surf-Mate Jr. rack in its current configuration.
Compatibility Conflicts
Physical Space Conflict: CURT front hitches (such as models 31432 for JK or 31086 for JL/JT) are "concealed" designs that mount to the frame rails behind the factory bumper. The Rampage Rock Rage bumper is a heavy-duty steel unit with an integrated winch plate and deep-reaching side supports that occupy the same physical space as the CURT hitch’s main cross-tube.
Bull Bar Obstruction: The Rock Rage bumper features a round bull bar that extends 9 inches out from the bumper's front surface. Since the Surf-Mate Jr. is 10.5 inches from the hitch pin hole to its rear upright post, the bull bar will likely physically block the rack from being fully inserted or cause the rack to sit too close to the bar for safe use.
Recommendation & Possible Solutions: Before purchasing the bumper, it is highly recommended to measure the distance from your current CURT receiver to the front-most point of your vehicle. If the Rampage bull bar's 9-inch protrusion exceeds this, you will definitely need a hitch extender to use your cooler rack.
Compatibility Conflicts
Physical Space Conflict: CURT front hitches (such as models 31432 for JK or 31086 for JL/JT) are "concealed" designs that mount to the frame rails behind the factory bumper. The Rampage Rock Rage bumper is a heavy-duty steel unit with an integrated winch plate and deep-reaching side supports that occupy the same physical space as the CURT hitch’s main cross-tube.
Bull Bar Obstruction: The Rock Rage bumper features a round bull bar that extends 9 inches out from the bumper's front surface. Since the Surf-Mate Jr. is 10.5 inches from the hitch pin hole to its rear upright post, the bull bar will likely physically block the rack from being fully inserted or cause the rack to sit too close to the bar for safe use.
Recommendation & Possible Solutions: Before purchasing the bumper, it is highly recommended to measure the distance from your current CURT receiver to the front-most point of your vehicle. If the Rampage bull bar's 9-inch protrusion exceeds this, you will definitely need a hitch extender to use your cooler rack.
Larry F.
Is this bumper satisfactory for flat towing a Gladiator behind a motorhome?
No, the Rampage Products 99306 Rock Rage Front Bumper is not rated or recommended for flat towing a Jeep Gladiator behind a motorhome.
We'd recommend looking at the LoD brand, which offers frame tie-ins and tow bar adapters. Their bumpers with those add-ons are rated for flat towing.
We'd recommend looking at the LoD brand, which offers frame tie-ins and tow bar adapters. Their bumpers with those add-ons are rated for flat towing.
Jake S.
I saw in an installation video that the bumper did not fit into the brackets on the jeep. Will this product fit on to my 2023 Sahara unlimited 4xe?
Yes, it will. These are the fitment notes you need to be aware of: The JK and JL 4-Bolt Fog Lights are a direct install. The JL 3-Bolt Fog Light requires modification. For the JK and JL with metal bumpers, their fog lights will not fit.
Greg W.
What is the recommended torque setting for the mounting bolts/nuts?
For Jeep aftermarket bumper installations, torque the 1/2" bumper bolts to 80 ft-lbs and re-torque after 1000-3000 miles.
Nicholas M.
Does this block the factory front trail camera?
This bumper and grille guard will not block the trail camera.
Jason M.
Does this bumper use 3/4” or 5/8” D rings?
This will accept 3/4" D-rings. Thank you for the question.
James P.
Could y’all give me the dimensions of the winch bolt pattern please
10" x 4.5" standard winch mounting. Thanks for your inquiry.