Give your Wrangler JL an aggressive off-road look with a Smittybilt XRC Gen2 Rear Bumper. This bumper was made with off-roading in mind with it's angled corners to improve clearance for rock crawling and hill climbing & welded D-ring points for recovery. The bumper is equipped with light tabs that accommodate (2) 9" in diameter LED Lights which are included in the package. Another great feature of this bumper is the built in class III hitch for true towing. Manufactured from 3/16" cold rolled steel for added strength & protection then coated with a nice light textured finish to protect from corrosion.
Features: Heavy duty 3/16" cold rolled steel for amazing protection against rocks or whatever you encounter on the trails. The high angled corners are perfect for those steep inclines or declines while the redesigned D-ring & jack point mounts make great recovery points.
LED Lighting: (2) 9" in diameter LED Lights are included to illuminate the rear for back up lighting needs.
Class III Hitch: 2" receiver hitch that is integrated into the bumper and bolts directly to you OE mounting points.
Bolt on Design: Making installation a breeze so your Jeep will be trail ready in no time flat. All hardware is included.
This bumper will NOT replace the factory plastic bumper. Designed only to replace the factory steel bumper.
- Rear Bumper
- License Plate Mounting Bracket
- (2) LED Lights and Light Mounts
- Features: D Rings, Integrated Winch Mount
- Style: Full Width Bumper
- Material: Steel
- Shipping Weight: 113lb
- Shipping Dimensions: 74in x 19in x 10in (L x W x H)
Jeep Wrangler 2-Door (JL)
- 2020 Jeep Wrangler 2-Door (JL)
- 2019 Jeep Wrangler 2-Door (JL)
- 2018 Jeep Wrangler 2-Door (JL)
Jeep Wrangler Unlimited 4-Door (JL)
- 2020 Jeep Wrangler Unlimited 4-Door (JL)
- 2019 Jeep Wrangler Unlimited 4-Door (JL)
- 2018 Jeep Wrangler Unlimited 4-Door (JL)
Customer Submitted Photos
Smittybilt XRC Gen2 Rear Bumper Reviews
My new rear bumber, is sooooooo much better than the plastic bumper! Strong and solid!
Great bumper. It will, in fact, replace the plastic bumper. I have a Rubicon JL with plastic bumper, no backup sensors. Replaced very easily. Instructions are non-existent but the install is straight forward. Includes plugs for the backup sensor holes. License plate relocation kit is poorly designed but it works. Makes it a pain to remove rear tire. Remounting the trailer wiring plug causes it to hang pretty low in order to clear the bottom of the bumper, i can see it getting smacked by rocks. Bumper would get 5 stars by itself, lack of instructions and license plate relocation goofiness gets it four overall from me.
This bumper is solid, stout, and enhances the look of my Jeep. Measured no sag in rear after install. I like that this includes LED lights and I opted to wire them to the reverse lights. I gave it 4 stars because of the license plate relocation. If you were to use it, then you need to re-route the license plate light wiring to the tailgate, and figure out a way in which you can still remove the spare tire easily. You can do it, but with great effort. Currently, I’m using a rubber coated bar magnet to temporarily mount the license plate under the driver side tail light, and will wire LED screw bolts to the original license plate wiring to act as a license plate light until I can find a permanent mounting solution. My bumper did not come with sensor plugs, but I emailed Smittybilt and they’re shipping them no problem. Quadratec price matched a sale on this bumper about 1 week after I purchased, and refunded $93. Very happy overall.