Chat with us, powered by LiveChat How To Keep Your Jeep Tires Properly Inflated | Quadratec Skip to main content
How-tos

by Matt Konkle
Managing Editor


The whole thing seems simple. You head out in the morning and notice your passenger front tire looks low. So you make a mental note to stop by the gas station on the way home and add some air back into that rubber.

Problem solved, right?

Maybe.

Here is the catch. Visually that tire may appear low, but is it though? It could just look that way and actually have plenty of pressure — especially on larger aftermarket tires. Then you’ve just wasted time on something that did not need to be addressed.

Then again, if a tire seems low, it could be significantly low on air pressure. And that is not the best thing as an underinflated tire is a primary cause of premature wear — not to mention more frequent trips to the gas station and degraded ride quality. Yup, low tire pressure is not just an isolated thing. It can severely affect important (and expensive) components on your Jeep.

So how do you really know when your daily driver Jeep tires are low on pressure, what is the proper inflation amount and when is the best time to check?

Well, today’s more refined Jeep vehicles make it pretty easy. That’s because each wheel has a monitoring system attached to the valve stem that continually ‘talks’ to the vehicle’s computer; letting it know when tire pressure drops below an acceptable level.

Should that happen, you’ll see a yellow-bracketed exclamation point pop up on your dash. Then, you can cycle through the information display until a tire pressure screen appears. This will show you the current pressure of each tire.

While this is a helpful system, it is not foolproof as the warning normally does not kick in until a tire is somewhere around 25% or so below manufacturer specs. Plus, you may have an older Jeep that does not have this system equipped.

Overall, the best way to keep track of your tire pressure is the good, old-fashioned, check-it-yourself method. And that involves using some type of measuring device. On average, tires will lose about 1 psi (pounds per square inch) each month and can also lose 1 psi per 10 degrees of temperature change. So taking a look at your tire's pressure at least once a month, or whenever there is a decent temperature variation, is certainly recommended.

As far as the perfect pressure rating; anyone with stock factory tires can find the manufacturer’s recommended cold inflated psi pressure number on a placard label somewhere in the front driver door sill area. That’s right – cold inflated. This doesn’t mean find the coldest area and then fill your tires with cold air, but rather taking a tire pressure reading after the vehicle has been parked for three or more hours.

If you do happen to take a tire pressure measurement when the tires are hot – meaning you’ve driven a bit — the world won’t end. Just remember that reading will be somewhere around 4 psi higher, so make sure you compensate if filling those tires after driving for awhile.

Another thing to remember; your respective tires will have a psi pressure number branded on the tire's sidewall which you may think is the correct number to follow when filling. But that number is simply the maximum recommended inflation pressure for the tire under load, and not the correct pressure to use for regular driving. When checking and adjusting tire inflation pressures, the correct inflation pressure for everyday use is always the one found on the vehicle’s tire information placard label.

Now, for many, replacing stock tires with something larger is one of the more important modifications after purchasing a Jeep. And those new tires will certainly look great, but can cause issues if you are not careful, as they may not have the same psi requirements as factory.

For example, your stock 255/75/R17 Jeep tires may be rated at 35 psi, however those new Mickey Thompson Baja Boss All Terrain tires could have a lower recommended pressure. Perhaps something like 32 psi. So it is definitely best to either check online or call your tire manufacturer and see what pressure setting they recommend.

You may even want to experiment a bit and see what psi level gives you the best ride. When you find a setup you like, you can check potential tire wear by performing a chalk test. This involves marking a section of your tire with chalk, then seeing how it reacts on the tire after driving a short distance forward and backward — maybe 50 yards or so — on a concrete or asphalt surface.

If the chalk is only worn off on the tire’s center, then drop the tire pressure slightly and redo the test. With small adjustments, you should soon see the chalk wear off evenly and across the tread.

This may be a time-intensive process, but one which should ensure your aftermarket tires are set to a proper pressure for good tire wear. After all, larger aftermarket tires are quite a bit more expensive than factory so protecting that investment from premature wear is important.

Those of you with later model Jeeps that have TPMS modules can re-use them on larger tires, but always verify the units have been reset to correct pressure. Your installer or dealership should be able to calibrate new TPMS settings during tire installation, but you may want to purchase a tuning kit — especially if you are adding a suspension lift or other new components that require things like a speedometer or shift point adjustment.



Related Articles:

Best Jeep Summer Accessories

Top Ways To Tame A Noisy Soft Top

Top Five Jeep Maintenance Tips

Top Jeep Articles

  • August 26, 2025
  • 4 min read
Spare Tire Delete: The Pros and Cons for Your Jeep Wrangler or Gladiator
Ditching the rear spare is more than just a look—it’s about performance, practicality, and personal preference.
READ MORE
  • August 25, 2025
  • 3 min read
Day Five at the Smoky Mountain Jeep Invasion: The Jeep Spirit Takes Over Pigeon Forge
From the Great Smoky Mountain Parkway parade to late-night parking lot meetups, Jeep life spills beyond the LeConte Center and into the heart of town.
READ MORE
  • August 22, 2025
Day 4 at the Smoky Mountain Jeep Invasion: A Rolling Showcase of Builds and Ideas
A rolling showcase of Wranglers, Gladiators, CJs, and more — Day 4 highlights how the builds at Smoky Mountain Jeep Invasion spark ideas and inspiration.
READ MORE
  • August 21, 2025
  • 3 min read
Seven Slot Dispatch 8.22.2025
Weekly Jeep-related news items from around the industry and community.
READ MORE
  • August 21, 2025
  • 4 min read
Day 3 at the Smoky Mountain Jeep Invasion: People, Passion and Purpose
From family traditions to first-timers, Jeepers are what keeps this event growing. And its not always about the products.
READ MORE
  • August 20, 2025
  • 3 min read
Day 2 at the Smoky Mountain Jeep Invasion: Move-In Day
Vendors, Jeeps, and energy fill the LeConte Center grounds as move-in day transforms anticipation into reality.
READ MORE
  • August 19, 2025
  • 4 min read
Buc-ee’s, Jeeps, and Smoky Mountain Vibes: Day One of the Jeep Invasion
From Beaver Nuggets to bumper badges, Buc-ee’s is more than a pit stop—it’s where the Jeep community gathers on the way to Pigeon Forge.
READ MORE
  • August 15, 2025
  • 7 min read
Quadratec Celebrates 35 Years Serving Jeep Enthusiasts
Company still focusing on its core tenets: better and faster service, and better pricing.
READ MORE